Member record · ID 49599
afinepoint
17 posts recovered 2 threads started First seen 17 Nov 2023 Last seen 23 Apr 2025
Threads started
2 in the archiveRecent posts
All 17- What to look for before purchase - 2007 RWB model I own an 07 25th anniversary RWB. I loved it and it currently has 43734 miles. Just about all highway and back roads. Some track days but as we know the VFR with it's side radiators doesn't like being pushed. Regular…
- 2007 Another no start issue Purring like a 800cc kitten.
- 2007 Another no start issue Flow test SAT. Minimum required 150 cc/ 10 sec. Results 720cc/10 sec.
- 2007 Another no start issue Relay replaced. It was bad. A real pain to remove from ECM plate. FYI pushing up while twisting to the right worked. There is a frame member mm's above it that will prevent pulling straight off. Apply gentle force to…
- 2007 Another no start issue Honda pump $742. Aftermarket $90. Manufacturer Yezoauto. Amazon. No reviews. Thoughts? I know the cheaper is going to be a roll of the dice but there is that wonderful Amazon 30 day no question return window. Relay…
- 2007 Another no start issue Jumpered power to pump. Nothing. No flow from return line. Will order pump and relay. Also FYI 7/32 hose fits the overflow nipple perfectly. Use a brake hose clamp.
- 2007 Another no start issue Fuel relay decided to fail so I'll add that to the list.
- 2007 Another no start issue Got back to the VFR. There is 12V at the pump for 3 seconds with key to ON. I can still hear a faint sound in the tank which stops when the FI light goes out. Listening with an automotive stethoscope I can't hear a…
- 2007 Another no start issue I'd like to do a pressure test however the manual describes Honda's required adapter and sealing washers. I'll check the relay then look at doing a Fuel flow rate check. That should tell me if the pump is degraded or…
- 2007 Another no start issue Thanks guys. I'll move it to the top of the list. I guess I was thinking can't hear it clearly "eh must be primed". The smell of gas misled me as well. I was expecting more sound. I got up early for the quiet. Turning…
- 2007 Another no start issue I thought about it but having the FI light extinguish as it has always done (KO no cranking) and unburned gas out the exhaust when cranking made me doubtful about the pump being an issue. I never found a fuse labeled…
- 2007 Another no start issue To get to it my 2007 decided to abruptly not start days ago. It sits under a cover and I start and run the engine periodically. I can't ride it as I'm sorting out a clutch issue. Perhaps more of that later.. The bike…
- New OEM clutch pack. Clutch not engaging Will rebuild master cylinder. Only kits exist can not get new master cylinder. Bike too old. So I will not be replacing the orifice but plan to blow it out.
- New OEM clutch pack. Clutch not engaging expvet, 11/18/2023 at 12:37 AM The master/slave on the clutch can be tricky to bleed properly. When I rebuilt both on my 6th gen it seemed as if the typical master to slave bleed had gone well but I was getting poor…
- New OEM clutch pack. Clutch not engaging No pressure being retained. Opened bleed port on slave and little came out. Nothing found in master cylinder bleed port but I did not have a fine wire to probe. I just poked with a small paper clip. Placed bike on…
- New OEM clutch pack. Clutch not engaging Like a check valve.. That makes sense. I was thinking the pressure plate is acting like it's being held away from the disks.
- New OEM clutch pack. Clutch not engaging Installed new clutch on 2007 800a. Flushed clutch fluid. Changed oil using Honda recommended type. Motorcycle did well for ride around neighborhood which is about 2 miles. Took bike out today. Was not engaging after…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.