Member record · ID 29070
Dedofnite
20 posts recovered 0 threads started First seen 18 May 2014 Last seen 26 Feb 2015
Recent posts
All 20- What's The Deal Here? Duc, I stopped buying from CG a year ago, same story. I went in to buy some Repsol 10/50 race that I have been buying from them for the last 10 years, and they had none, in fact they had no 10/50 at all. Same…
- Sad Day But I'm Lucky Hey Rob, Evasive moves are always iffy in the wet, (I slid under a taxi in Germany once!), really glad to hear your story from you. Sounds like the knee got twisted a bit, maybe ACL tear, I've been through that one,…
- Blessed To Be Alive! Nap, Glad to hear you are ok. Tough call on left turners, sometimes the split second decision maneuver doesn't work. Had a couple of those. Hard to tell from the pic, but it looks like the fairing and bracket took most…
- Caption "insert Here" "Maaak, Maaak! Too mucha Red Boola! Let me open zee drain plugeh before you explodeh..."
- Well I'll Be Damned! WAY TO GO, CHUCK!!! :fing02: I think they need some V4s in NHRA drags, so keep practicing! What did you run against, or will we see that in the video? :laugh: Ded
- Well I'll Be Damned! zRoy is right on. I sent you a PM, Chuck. Ded
- Should I Stop Riding After Noticing The Oil Level Is Over The Maximum? Oh yeah, forgot about blowing out the breather! Thanks, Busy! :happy: Ded
- Should I Stop Riding After Noticing The Oil Level Is Over The Maximum? Hey Josh, If there were massive damage being done to the engine by your day to day riding, you would probably know it by now. Oil level slightly too high is not a real big deal, but if, for instance, you accidentally…
- More On Trail Braking Df, The LBS seems to work fine on the Blackbird, at least on the street, where I am not spinning the rear wheel. If anything, it forces a little more counter steer input, partly due to the bike's weight, I think. On the…
- Noise From Bike After Cleaning Hey Dave, What Beck said, and a good wash can loosen some grit around the calipers, possibly causing the pads to not retract smoothly. Don't know the mileage or age of your brake piston seals and pads, but if the sides…
- More On Trail Braking Me too, Duc! (that's how I keep from hitting you in the corners... :tour: ) ( Oh, yeah, and the throttle is on the right! ) :laughing6-hehe: Ded :dry: Just kidding! You're almost too fast for me to ride with anymore!
- 4Th Honda. 1St Vfr. 2014 Hey Tim, Nice opening post! Thanks for the report on your new VF experience. I haven't ridden one yet, just sat on them. :sad: So far it sounds like a keeper, and I think Honda did a good job with keeping the "does…
- Hesitation, Stumbling, And Occasional Surging - What Are We Missing? Hi Laney, Sounds a lot like the thermostat. Not sure what you meant by plugs looking like 30,000 miles. Were the electrodes eroded, or did the plugs look black and sooty? The thermo is a cheap and easy fix. If it's bad,…
- Is This Chain Dead? :) Capn, I get a pretty consistent 20,000 or so with a good, high end chain. Usually run the best from RK or DID, just like Spud said. I don't change sprockets very often, just watch them for wear. Stock, hi quality steel…
- Is This Chain Dead? :) Lots of good info on this thread! (and some not so good...) :rolleyes: Carver! Where the heck did you get... "that red stuff on the chain is the Special High Temp Grease they use inside the o-ring chains..." ??? That's…
- Best motogp season no spoiler Ditto! This one actually kept me awake! :ohmy:
- Anyone Using Hid Headlights? Hey Hogan, Not sure about your bike, but I installed an HID kit on an '06 for someone about 2 years ago. The light output was impressive, but the 6th gen headlight lenses are not designed to focus the light from those…
- Greetings All Hi Phil, Welcome to the forum of Honda V4 things. Wow! Nice find. Looks like an unmolested, stone stock, low mileage. garage kept '86. I have an '85 that is a left over back-up bike from my racing days. Yours is…
- California Tour 2014 Lorne, Nice write up and pics. Looks like a cool tour with a good group. Ded
- Does Anyone Have Experience With This Chain Tool? The picture looks to me like there is a cone on the press pin to flare the rivets. I can't think of why they would make one without it. Seems like a nice simple tool, that will fit in a tool kit nicely. Having to carry…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.