Member record · ID 43560
BSR67
21 posts recovered 1 thread started First seen 7 Jun 2021 Last seen 11 Jun 2021
Threads started
1 in the archiveRecent posts
All 21- Fuel Injection Light on after cutting out Thanks Grum. Good advice as ever. I’ve managed 84 miles on the bike without a hitch so far. Will undertake the busbar mod as soon as possible - soldering the group together. Shocks me, as it does others, how undersized…
- Fuel Injection Light on after cutting out Hi Grum/All It’s a damn shame the video doesn’t work. It shows me running the multimeter along the pins with the black lead on the negative battery terminal which we know is securely earthed. Taking the photo attached…
- Fuel Injection Light on after cutting out Hi Grum/All This is the busbar. Interestingly there is a natural break between the two sides at the far end of the plug (the opposite end to the main earth wire). You can just about see it in Photo 2. Alex
- Fuel Injection Light on after cutting out Step 2 Continued. Video checking the pins on the grey ground bar. One side at a time. One connector is slightly higher - the second pin in the second video. Will welcome your thoughts on that second pin and also, the…
- Fuel Injection Light on after cutting out Stage 2 continued. Plug exposed. Some light scorching. The lightly scorched terminals across from one another read 0.08 ohms when linked back to the battery negative. Others give no reading. Some are Differing values.…
- Fuel Injection Light on after cutting out Step 2 Here is the earth block. I’ve unwrapped it. It is far easier to access from the top. Going to separate the cap shortly. alex [image: 398BBE2E-4E7E-41DB-A917-3CF487B1A25E.jpeg] [image:…
- Fuel Injection Light on after cutting out Hi Grum A small step. Photograph attached of ground anchor point left hand side of the bike (as you sit on it). It shows the two green/pink wires. Also two further green wires. The second photograph shows the battery…
- Fuel Injection Light on after cutting out 9 hours ago, Grum This is becoming a little frustrating! Until you confirm the frame grounds as in step 1 are either good or bad, you don't need to be jumping into step 2 with the harness ground block. Your problem just…
- Fuel Injection Light on after cutting out Hi Grum I’m going to be reporting back early next week. I’ve investigated, found the plug but only have basic tools here so need to collect a load from home at the weekend to allow me to remove more parts. The plug is…
- Fuel Injection Light on after cutting out I mean report back! Wish I was having a drink!!!!! 😀 I’ll report back later ….!!!!!! Alex
- Fuel Injection Light on after cutting out Thanks Grum Will be checking later. Will revert. Do you know where an ECM test harness is available? Part number look up doesn’t yield any results. Alex
- Fuel Injection Light on after cutting out Thanks Grum! Amateur hour continues! 😄 I'll re-check later today and revert, plus the findings from under the panel. I haven't checked the grounds on the ECM yet - do this at the same time or after the earth bar…
- Fuel Injection Light on after cutting out Hi Grum Whoops - amateur hour last night! Forgot about the 5,000 readings. Here they are: Voltage pre-start - 12.69v Voltage after start at 5k rpm - 14.41v Voltage at 75 Centigrade and at 5k rpm - 14.39v Resistance…
- Fuel Injection Light on after cutting out I’ve cleared the fault code. FI light stays solid when dealer plug bridged. At the moment FI light goes out after removing bridge ……..!!!
- Fuel Injection Light on after cutting out Hi Grum Here we go: Battery Voltage pre-start (battery off bike) 12.77v Battery Voltage pre-start (battery fitted to bike) 12.77v Battery Voltage immediately post start 14.33v Battery Voltage after approx 5-7 minutes,…
- Fuel Injection Light on after cutting out 14 hours ago, Grum Hi Alex. Good to know your bike at least runs and Main Fuse B and its wiring are in good shape. Its really important chasing the fault you have that when referring to the Fi Light, what is the…
- Fuel Injection Light on after cutting out Hi Grum Connections look to be in good shape. Multimeter landing tomorrow. Will update. Alex
- Fuel Injection Light on after cutting out Hi Grum Connections look to be in good shape. Multimeter landing tomorrow. The bike does run but the FI light stays on. Will update. Alex [image: 645754E3-AE27-4FC7-B03D-D70139C7D6C8.jpeg] [image:…
- Fuel Injection Light on after cutting out Hi Grum! Good to speak again! Bike has been faultless until now - and I've covered 650 miles. I'll check the connector as directed. Also, will buy a multi/test meter. As you'll recall I work away from home in the week,…
- Fuel Injection Light on after cutting out 35 minutes ago, BSR67 OK, so strange happening this evening on a 160 mile ride. Was pottering along at around 80 mph on the A1 and the bike suddenly cut out (I saw the Rev counter drop to zero) and a pulled over and let…
- Fuel Injection Light on after cutting out OK, so strange happening this evening on a 160 mile ride. Was pottering along at around 80 mph on the A1 and the bike suddenly cut out (I saw the Rev counter drop to zero) and a pulled over and let the clutch out on…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.