Member record · ID 636
Finleyville
13 posts recovered 4 threads started First seen 30 Apr 2015 Last seen 24 Aug 2015
Threads started
4 in the archive- Head Bearing Replacement Answer Needed Finleyville · 27 May 2015 – 26 Sep 2016
- How Would You Perform This Operation? Finleyville · 12 May 2015 – 13 May 2015
- Fast Answer For Rear Shock Removal Needed Finleyville · 11 May 2015 – 20 Jul 2016
- What Else To Do To My Y2K Front End? Finleyville · 30 Apr 2015 – 30 Apr 2015
Recent posts
All 13- What's The Hottest 5Th Generation Can? Post Your Pics.... lanesmatb How about a 5th gen Two Brothers CF shorty high mount can? If you EVER get rid of your bike I will swap/buy that exhaust from you in an instant.
- Head Bearing Replacement Answer Needed FJ12Ryder If there's a groove in the seating area, there's also a ridge where the material from that groove went. The third picture from the top doesn't look good at all. It looks like some material is pushed up and…
- Head Bearing Replacement Answer Needed Well, it has been two days of fussing with this with no joy so I am going to step back and try again in a couple of days. I am wondering if I should purchase another All Balls set to see if the lower race might be the…
- Head Bearing Replacement Answer Needed What it I bought a long bolt with a nut to pass through both Harbor Freight seating dies and tightened them together (without the bearings in place) to seat the bottom one. Think that could work?
- Head Bearing Replacement Answer Needed Anyway... I am replacing my steering bearings with the All Balls 22-1020 tapered set. I have seated the upper race and am having trouble with the lower. I have seated it flush with the cast frame using the Harbor…
- How Would You Perform This Operation? @zoomzoom I will have to try your magnetic coathanger trick when I get back from my business trip. Thanks. @Dutchy Yes, that is the cf hugger I own. Isn't it pretty? You are right in understanding which spacer was lost.…
- How Would You Perform This Operation? a very specific, non-standard, non-Honda washer/spacer fell down and perfectly fell into the space If you know the washer dimensions, or can figure out what they should be, leave it there and get a new one. :comp13: I…
- How Would You Perform This Operation? Anyway... While removing my carbon fiber rear hugger to service my rear shock, a very specific, non-standard, non-Honda washer/spacer fell down and perfectly fell into the space between my catalytic convertor and its…
- Fast Answer For Rear Shock Removal Needed Well, thanks to all of your help, I removed the shock. What worked for me was to remove the right rearset and loosen the left rearset. That allowed the swingarm to fall all the way to the cat convertor. Only then did I…
- Fast Answer For Rear Shock Removal Needed Well, the right rearset is moved away the and heat shield are already off . It looks like you removed the whole rear swingarm from that second pic. I would rather not do that. By looking at the bike I cannot fathom how…
- Fast Answer For Rear Shock Removal Needed Anyway... I tried to search but I did not see my answer. I am removing my rear Ohlins shock off my 2000 VFR to be serviced. Is there anyway to remove the whole shock without removing the whole catalytic convertor and…
- What Else To Do To My Y2K Front End? So I should also replace the fork sliders and seal along with steering stem bearings. Got it. Does anyone know who can service my Ohlins rear shock including changing out the spring for a proper setup?
- What Else To Do To My Y2K Front End? Anyway... I either plan on sending my front forks to Daugherty Motorsports or ordering their fork cartridge kit and doing it myself. (Little nervous about that one) I have a couple of questions. After removing the front…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.