Member record · ID 23587
nutball
19 posts recovered 4 threads started First seen 17 Jan 2012 Last seen 17 May 2012
Threads started
4 in the archiveRecent posts
All 19- Suggestions on mods another free one i just did was lowering the front end 10mm. it made an amazing difference in steering quickness, and was very quick. might wanna give it a whirl. This doesn't throw the geometry off? How much quicker is…
- Suggestions on mods another free one i just did was lowering the front end 10mm. it made an amazing difference in steering quickness, and was very quick. might wanna give it a whirl.
- Minding his business ... then wham! just more proof speeding saves lives!
- Lowering the front end?! I got impatient and did the front end drop, took 15 mins and I dropped it 9mm. all I can say is HOLY SH&@T!!! why in the world didnt I do this a year ago? actually why didnt honda do this from the factory?!?! the turn…
- Lowering the front end?! johnmark101, on 10 May 2012 - 11:22 AM, said: If you don't mind a little extra work, raising the rear ride height is a slightly better alternative as it will not decrease your ground clearance. I raised the rear ride…
- Lowering the front end?! I happened to be at the track a few weeks back, whilst making small talk to the other motorcyclist I got a piece of advice saying I should lower the front end of the bike just a tad, apparently on bigger/heavier bikes…
- Suggestions on mods [image: View Post]VietHorse, on 06 May 2012 - 05:34 AM, said: Anyone run Dynotest after PAIR valve and flapper mods to see the differences? I'm pretty sure I read a post where someone dynoed after pair flapped mod and…
- Suggestions on mods Rodney, nice bike... looks oddly familiar to mine.... anyway I painted my heat shields and muffler tips flat black with engine enamel and so far no issues, just make sure its very dry between coats. also your fender mod…
- Frame slider suggestions? Function over form pls. [image: View Post]Larrakin, on 18 February 2012 - 05:59 AM, said: Just wanted to out it out there that an Australian manufacturer 'Oggy Knobs' does a no cut option frame slider which has very good reviews. Not cheap and…
- Frame slider suggestions? Function over form pls. Roland, have you made any headway with T-rex? I would be very interested in a set of those sliders+brackets!
- Where can i get a Joe rocket hrc replica leather jacket?! Ive been looking for days and cant seem to find a place to buy one of these jackets! maybe if someone has a used one they dont want anymore??? If anyone has any info on where to get one post it up!! Attached Images…
- Make it RAWR for less than $100 Thanks for the comments! I had a chance to do a 2 hour ride today and can report ZERO issues with the rear light, at the end of the ride it was luke warm... also as for sound, i happened to pass a mini van (good for…
- Make it RAWR for less than $100 thanks everyone for the input, as for the tail light heat I will start drawing up some kind heat shield just to be on the safe side! also as requested i have made a crap sound clip : [image: 7c] 7c sound bite
- Make it RAWR for less than $100 Fred, I have to thank you again for the freebie pipe! your right about the extra slag, sadly my welder doesnt accept gas, unfortunately money is an issue at the moment so i had to go cheap : :tour:
- Make it RAWR for less than $100 Looks great! Do you think you might get a bit too much heat onto the plastics (rear lights and other tail parts)? I was thinking the same thing (after everything was welded up......) but I ran it for 40 minutes, eng…
- Make it RAWR for less than $100 Aftermarket mufflers really aren't all that expensive. Ebay is rotten with them. They don't have to be new. Folks have spliced a pair of 2" aftermarket cans to the stock headpipes by means of a couple of adaptors. I did…
- Make it RAWR for less than $100 So Ive been wanting a louder exhaust (I came to this conclusion as some idiot on a cell phone slowly merged into my lane without realizing i was there...) but i'd rather not pay $1000. what to do? make my own. I came up…
- New Exhaust mod Idea.. input needed [image: View Post]Baileyrock, on 17 January 2012 - 03:32 PM, said: I think your concept is a solid one, BUT! The stock Y-pipe is fairly small and restrictive using two oval feed pipes approx 1 1/2" dia. which is equal…
- New Exhaust mod Idea.. input needed So Ive been checking out the mods that are out right now ( ive also learned how to weld so Im searching high and low for new projects ) I like the idea of keeping the stock look but i dont like the loss of…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.