Member record · ID 22918
wshtb
25 posts recovered 6 threads started First seen 7 Jun 2011 Last seen 12 Dec 2012
Threads started
6 in the archive- Does 5Th Gen Exhaust Fit 6Th Gen? wshtb · 12 Dec 2012 – 12 Dec 2012
- installed pair block off plates, and a question wshtb · 17 Jun 2012 – 22 Jun 2012
- rant: low beam bulb holder is crooked by design wshtb · 22 Nov 2011 – 23 Nov 2011
- Anyone use soft bag and Leo Vince exhausts? wshtb · 16 Nov 2011 – 20 Nov 2011
- front and rear brakes uses the same pads? wshtb · 28 Oct 2011 – 6 Apr 2012
- Back on the Forum, and look what I did today! CoachCraven · 7 Jun 2011 – 9 Jun 2011
Recent posts
All 25- Does 5Th Gen Exhaust Fit 6Th Gen? I haven't ordered yet so I don't know for sure. But I expect there to be a hanger. So if the header bolts up fine, the worst that will happen is I'll have to fabricate a custom bracket.
- Does 5Th Gen Exhaust Fit 6Th Gen? I have been contemplating with GP-style exhaust. Found one but it is for 5th gen. So I wonder if a 5th gen VFR exhaust will bolt up to the 6th gen header?
- installed pair block off plates, and a question This morning I fired up the bike and it idled perfectly around 1300rpm. Viola! No need to mess with the fast idle wax unit. Now after riding it at median speed (~30-40mph) for ~45 minutes I have to say the popping on…
- installed pair block off plates, and a question [image: View Post]2thdr, on 18 June 2012 - 06:53 PM, said: Don't think you're going to find too many loud straight pipes enthusiasts here to bounce ideas off. But I've been wrong plenty before ... Sent from my DROIDX…
- installed pair block off plates, and a question [image: View Post]kaldek, on 18 June 2012 - 06:53 PM, said: Can you tell me what year your bike is? My 2002 needed no adjustment of the fast idle wax unit when I installed block off plates, but the 2006 motor (and ECU)…
- installed pair block off plates, and a question [image: View Post]spud786, on 17 June 2012 - 03:55 PM, said: Did you say you have modified exhaust , cause I get zero popping on decel with stock config and everything Hooked up from the manufactuer? Yes, I ran a short…
- installed pair block off plates, and a question timmythecop, removing the pair system did get rid of the popping on deceleration, so it is an improvement for me. Plus less weight, if that matters on a 500lbs bike.
- installed pair block off plates, and a question Yesterday I finally got the free time to install the pair block off plates. Also took the time to wire up a relay for the HID projector lights because the stock wiring doesn't seem to handle the surge of current at…
- Ordered a K&N filter and it doesn't fit..WTF? When I installed a K&N air filter on the VFR I didn't have fitment issue after removing both O-ring. It is a tight fit, but that's the purpose. You don't want air to enter the air box from anywhere outside the filter…
- "HID" LIGHTS, and Adjustments of any headlight Here is Los Angeles there are so many people running their high beam at night. I used to flash them but very few responded, if ever. So I installed bixenon HID projectors in both the VFR and the truck. And I don't…
- rant: low beam bulb holder is crooked by design From what I can tell, both bulbs holders were turned clock-wise by a small amount relative to horizon. Because Morimoto projectors come with centering rings that assumes the bulbs are horizontal, the end result is that…
- rant: low beam bulb holder is crooked by design So I got the morimoto mini projector set. baked my headlamp in the oven, popped the lens shield, bolted on the new projector with the supplied centering ring, and so on and on until I finally put everything back…
- Anyone use soft bag and Leo Vince exhausts? Since there is no response, I have went ahead and took the stock cans off to see how it sounds with straight pipe. WOW!!! It is like going from a kitten to a roaring lion. So I got a short piece of curved tip from…
- Anyone use soft bag and Leo Vince exhausts? Does anyone use soft bags with their Leo Vince exhaust? I'd like to improve the sound of the bike with a pair of Leo Vince aluminum cans, but I'm worried about the bags melting without the heat shield. If you have used…
- front and rear brakes uses the same pads? [image: View Post]vanion2, on 28 October 2011 - 08:24 AM, said: I hope you shopped around because you could have picked up those exact same pads on amazon.com for $36.45 a set including shipping (almost $7 cheaper per…
- front and rear brakes uses the same pads? Thanks guys! Ordered 3 set of FA261HH.
- front and rear brakes uses the same pads? I'm planning to replace the brake pads with EBC double-H. EBC's online distributor suggests the front and rear brakes use the same pads: http://www.perfectbr...ts.asp?cat=4093 Is that right? I always thought the rear…
- Back on the Forum, and look what I did today! Thank you! It's good to be back.
- Back on the Forum, and look what I did today! [image: View Post]Gbam, on 08 June 2011 - 02:19 PM, said: What else do you guys produce? Any parts for the 3-4th gen guys? Unfortunately (my 93 is still in SO many ways the best bike I ever owned) all we have at the…
- Back on the Forum, and look what I did today! [image: View Post]Infidel, on 08 June 2011 - 12:06 PM, said: Welcome back to the Forums!! Thanks man!
- Back on the Forum, and look what I did today! [image: View Post]03vfrrider, on 08 June 2011 - 11:16 AM, said: So, what company is it? Don't you want to plug it? Who knows, you might start a run on your products...we're always looking for suppliers, right guys???…
- Back on the Forum, and look what I did today! [image: Posted Image] DSC00805 Or how about in red?
- Back on the Forum, and look what I did today! [image: Posted Image] New pics 166 Here you go!
- Back on the Forum, and look what I did today! [image: View Post]Monk, on 07 June 2011 - 04:49 PM, said: Welcome back.... Do you have any pic's of the guards? Thanks. I'll put a couple pics up tomorrow when I get back to work.
- Back on the Forum, and look what I did today! Haven't been on here for a long time (so long I forgot my password, so... new account), just started a new job and I figured you might be interested in the first project I was involved in. The company I work for makes…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.