Member record · ID 26599
Occse
16 posts recovered 1 thread started First seen 6 Jan 2013 Last seen 6 Feb 2016
Threads started
1 in the archiveRecent posts
All 16- 6500 Rpm Flat Spot When you went through the carbs did you inspect the slides and diaphragms?? Look for holes in them Also Was the secondary air filter gone? I went through a week of hell trying to solve a loss of power problem. Found goo…
- 3Rd Gen Vfr750F Ninja Zx14R Rear Shock Swap Any news regarding this project? I'm really on the edge of repairing the stock or make the best solution replacement from an other bike.
- 3Rd Gen Vfr750F Ninja Zx14R Rear Shock Swap Just took out the original one and replaced with the ZX14 shock? No machining works? How much did that raise the bike?
- Stucks At Around 6K The guy who made it is one of the Hungarian VFR club's member and made a lot of VFR's from the club. He is a motorcycle mechanic. If there would be any problem with the diaghragms he would have said that and would not…
- Stucks At Around 6K The guy who made it is one of the Hungarian VFR club's member and made a lot of VFR's from the club. He is a motorcycle mechanic. If there would be any problem with the diaghragms he would have said that and would not…
- Stucks At Around 6K The guy who made it is one of the Hungarian VFR club's member and made a lot of VFR's from the club. He is a motorcycle mechanic. If there would be any problem with the diaghragms he would have said that and would not…
- Stucks At Around 6K Yes, gravity will work fine Hey Dudes, It seems that the pump works like hell, it blow so much lifegiving liquid that I could water my garden with this pump. Here's some pics. http://kepfeltoltes....ltoltes.hu_.jpg…
- Stucks At Around 6K Yes, gravity will work fine Hey Dudes, It seems that the pump works like hell, it blow so much lifegiving liquid that I could water my garden with this pump. Here's some pics. http://kepfeltoltes....ltoltes.hu_.jpg…
- Stucks At Around 6K I found when my fuel pump failed, I could easily run it on gravity feed (My tank was near full) to get home - so it's good advice to bypass the pump first to see if it's this and if not go onto other possibilities. I…
- Stucks At Around 6K Couldn't try that yet, but if the pump can't pump the required quantity of fuel, can that be adjusted or I have to buy an other pump?
- Stucks At Around 6K It seems that my baby don't want to go above 6k rpm. I've changed last year the clutch plates (friction and steel) and the springs also. New motor oil with that. I didn't have a chance to ride it last year so I couldn't…
- 1993 Front Wheel Bearing P/n Could you tell me what is the best method to install the wheel between the forks? If I just push the shaft in the forks with the wheel and the spacers, after that tighten the bigger screw (60Nm) and after that the two…
- 1993 Front Wheel Bearing P/n I don't clearly see why it is recommended to be both side sealed bearings (2RS), if there's rubber seal from both sides. I'm thinking about to replace these with E2 signed "efficient" bearings, those only have metal…
- How To Repair Broken, Or Missing Abs Body Tabs, And Hair Line Cracks Resin It's common for ABS components to develop fatigue cracks, structural wear, and chipping. Realize your body parts are 20 years old, so you expect some required maintenance . May I request you post a few photos of…
- How To Repair Broken, Or Missing Abs Body Tabs, And Hair Line Cracks I'm thinking about strengthen my 3th gen's fairs with structurized fiberglass on the inner side. On the bolt connections priorized, but on my old fairings I can see which edges used to crack due to vibrations. What…
- R1 Suspension Upgrade For Christmas! (W/ Pics) Could you share the whole part list, stock and machined/modified you installed?
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.