Member record · ID 39880
Zarquon
59 posts recovered 1 thread started First seen 19 Jul 2018 Last seen 18 Nov 2019
Threads started
1 in the archiveRecent posts
Last 50 of 59- 6th gear noise on 5th Generation 36 minutes ago, Terry Doesn't look like it; the mounting bolt diameter is larger on the 6th gen 10mm vs 8mm on the 5th gen. Thanks Terry
- 6th gear noise on 5th Generation I finally got the chance to ride today, with a slightly looser chain adustment. The noise is still there but I think it cuts out at a lower rpm now. It sounds like the chain and kind of has a lugging engine beat to it.…
- 6th gear noise on 5th Generation 1 minute ago, Rush2112 5th gen motors and gear boxes are practically bullet proof. The PO might have changed the gears and not the chain. Go with a new set of chain and gears and you’ll be happy. They are maintenance…
- 6th gear noise on 5th Generation 1 minute ago, Rush2112 I’d be surprised if it is not your chain and sprockets. 6th gear low rpms accentuates the issue because of the power pulses from the syncopated firing order engine. That, plus tight and loose…
- 6th gear noise on 5th Generation I think thats where I need to go with this. Tinker with the chain and sprocket and if that doesn't help find a replacement engine to swap in when or if this one breaks.
- 6th gear noise on 5th Generation 4 hours ago, Grum What is the state of your chain? Would experiment with its tension then test ride. Too tight, too loose, lack of lubrication, worn out can all create strange effects and noises. Will look at this…
- 6th gear noise on 5th Generation My 5th generation is making a chattering noise in 6th gear (it sounds abit like the chain needs lube or is too tight). Its most noticable bellow 4000rpm and goes away above 5500rpm. To begin with I thought it was engine…
- 5th Gen brake Issues....again Good job fixing those brakes.
- New Member 98 VFR - Starting Cold is not great If you haven't already put fresh gas in the tank. Will help starting for sure. Try A good quality injector cleaner in a few tanks of gas. It might clean things a bit and help with the starting. The rear brake pistons…
- Overheating. Could it be the thermostat? It could be possible that you have an airlock in the system and it just needs to be burped out?
- Is this thing too hot? My gen 5 runs between 86c and about 98c under nearly all seasons and riding conditions. I'm based north of Sydney Aus where it gets hot in summer. I have also riden the bike well loaded to Cairns. It is a very rare…
- Just bought one...cheap. You can also unbolt and inspect the back of the r/r to see if there is any bulging, bubbling or blistering in potting compound the electronics are held in.
- '93 won't rev past 5000rpms Could be blocked or blocking air box inlet or clogged air filter. High fuel level in carbs or some other cause for over fueling when the carbs transition onto there main jets. Could be clogged main gets. The hard…
- Just bought one...cheap. I have the same model, same year. Bought with 38000km on it now 9 months later has 50000km. Issues include: head set bearings, clutch slave leak, water pump cover seal leak, blown r/r, dirty injectors, cheesey O rings…
- Soldering on the aluminum frame Taking off the tank is mostly about not making an accidental air fuel bomb out of it. A fire blanket around everything else should prevent an accidental fire. There should be no spatter etc, just the radiant heat from…
- SYDNEY RIDERS I got a blue Gen5 that needs an airing. I'm based on the Central Coast, so a loop ride up this way (Wisemans Ferry and Putty Road) with a couple of meet up points (Jerry's for me) along the route might be an idea.…
- Soldering on the aluminum frame I would not weld on or near a gas tank full or empty if it could be avoided it. If you have broken an aluminium tab from the frame, TIG welding is likely the most appropriate process to re attach it and its going to…
- 1998 honda vfr 800 , lack of power ? You might have some air in the clutch line. There is a trick to bleeding the clutch. Because of the angle of the banjo fittings on these bikes you may need to just crack the banjos (with a bit of paper towel under them)…
- 1986 VFR750R with fresh duco and decals. Nice work
- just picked up a '99 model - now what? On the bolts... Lube well with penetrating oil for 24hrs and use a small (low power) electric impact driver and a very well matched allen key bit. Be gentle, Good luck.
- Hesitation / loss of power at a constant rev Sounds like I need to add a job to the list on my gen5. I take it your in Aus. Was wondering who did your injector clean and what it cost?
- Brake issue assessment. Would you agree with my conclusion? Sorry I added some extra thoughts to my last post.
- Brake issue assessment. Would you agree with my conclusion? I wonder if the rear pistons are sitting true in their pots after pushing on the back of the brake pad. Perhaps rotating the pistons 90 degrees in their pots and/or replacing the rear pads if the wear is uneven. In your…
- Brake issue assessment. Would you agree with my conclusion? You probably already did this? I would be de mounting the rear caliper leaving the brake lines attached and working the pistons out with the rear brake pedal then forcing the pistons back in with clamps until all came…
- just picked up a '99 model - now what? Welcome to the board and great choice of bike. You will never need to adjust or replace a timing chain on your bike 🙂 First thing I did to my 2000 gen5 with 38000km on it was add a volt meter and a usb socket and phone…
- Testing Fifth Gen, Photo Is it Michael Jackson?
- 12v Power outlet plug mount/USB mount The wiring installation looks and sounds like its all propper. Watch for chafe on the insulation. Honda saw you coming with those brass inserts... Can you attack the shoulders of the key or get one cut that's got a…
- 12v Power outlet plug mount/USB mount Neat installation. Bitch about the steering lock. I would cry if my bike got nicked because the bars wouldn't lock... Surely you can shave the back of the plastic collar or the sides of the key to make it work? Does…
- 07 R1 Racecar Project Cranks but Won't Start I am unfamiliar with the R1 but, Is there someway to output error codes with a jerry rigged engine light? Make sure all the electrical slider connections are seated properly in their plastic plug housings. Sometimes…
- New VFR 800 Fi '99 owner... Frame sliders and Chinese fairing kits? Honda still has the matching fairing bolts. I got some recently from them. Watch out parking on soft ground... these bikes tip all by themselves... consider a spare brake and clutch leaver! Great colour by the way. The…
- new owner, need help with windscreen (it's too tall) I am 5'9" and have same problem with Corbin seat. I am sure they are made for tall people with big butts! I ditched the clip ons and put raised/raked handle bars on, fixed the issue. Or, butt augmentation surgery might…
- Quick question around compression in a "long sat" engine. My 2 cents. I don't think the compression test is indicative of anything... except that the engine has sat around for a bit and not been run. There's alot of shiny surfaces inside that machine that only keep fresh by…
- New 5th/6th/8th gen performance header now in production in USA sfdownhill, 1/28/2019 at 7:22 PM The dyno chart at the top of the post is from the first s et of dyno runs. After recording these, Jozef brought the bike back out to us - something was definitely wrong. To keep this…
- 4th gen silencer The thinking and practice has paid off. Stock look maintained and improved V4 note. Need to sound check in a tunnel or underpass! Enjoy
- 4th gen silencer I like what you've done. I Was thinking about doing something similar with a vintage Suzuki 600. Beef up the noise a little but keep the factory appearance. Now, I guess I better pick up tools and do it!
- Charging system performance upgrade It looks like what you've done will keep things going for a bit. I agree with JZH. Upgrade reg/rec sooner rather than later, because the originals are a known problem. (Mine blew at 40000km. One of the diodes fried and…
- New 5th/6th/8th gen performance header now in production in USA Wrap aluminium foil around the loose fitting pipe several times until it is a snug fit into the slip on. It's Ugly but functional!
- Cam reinstall - timing help needed Looks like you have done a fine job getting those parts clean.
- Cam reinstall - timing help needed 48 minutes ago, Stray 50 minutes ago, Stray got a seal/ filter kit on order from the USA. Will fit with silicone grease ( same stu ff a s brake calliper seals). I don't suppose you could post the suppliers web link? 🙄
- Cam reinstall - timing help needed Its nice to see the injectors wern't to bad given their age and milage but looks like I should probably be seeing to my seals in the not to distant future.? I was wondering if the throttle bodies had to be removed to…
- Fi cold starting If new fuel doesn't fix your cold start dificulty. Perhaps the starter valves need to be synchronized? This will also help idle smoothness. The workshop manual will tell you how to do this. My gen5 2000 model (which…
- Gas mileage on a 98 5th gen 3 hours ago, Terry I had an RF900 for 18 years, they are a good solid machine but a little uninspiring next to a V4. Have a look at the emulsion tubes in the carbs, mine wore oval over 50,000km and the fuel economy went…
- Cam reinstall - timing help needed Nice going... getting that b@$tard undone... progress!
- Newbie from AUS I have the same bike in blue and luv it. Just did Sydney to Cairns and looking forward to another great trip back in a few weeks. The reg/rec died on me in Brisbane (40,004km) my volt meter showed a low voltage problem…
- adkfinn's 5th gen 20yr refresh For info my Gen5 battery voltage sits between 14.0 to 14.4 too. It will drop to 13.0v at low rpm after a long ride when the r/r is hot. Great job (great thread) btw I look forward to reading about your suspension mods…
- Bit of favor to ask, would owners of the 5th gen send pictures of the head serial number? My yr 2000 5th gen is polished and stamped just like your first photo.
- how off is a stock speedo? 1 hour ago, FJ12Ryder Possible, but that seems pretty recent, and all Japanese motorcycle speedometers from the early 60's on have all been optimistic. I still think they did it just so it would look like you were going…
- how off is a stock speedo? This is the best explanation I can find for factory speedo error. From the RACQ WEB PAGE Quote Australian Speedo accuracy standards Australian Design Rule 18 sets out the accuracy standards for vehicle speedos. Until…
- Post your Voltmeter mount pics I admit a blue meter would fit better woth the theme... No holes needed. Its Just held on with double sided tape. The little green LED is the cruise control status indicator. [image: 20180818_120014.jpg]
- VARIABLE9’s V4 VFR VICTORY 14 hours ago, VARIABLE9 Thats awesome! Man you’re way more motivated than I am. You should do a write up and detail it out. Whats that on your muffler/peg bracket? A horn? Clean under the seat - yep when I bought it I…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.