Member record · ID 29396
Alhazred
32 posts recovered 2 threads started First seen 12 Aug 2014 Last seen 14 Jun 2017
Threads started
2 in the archiveRecent posts
All 32- 5th & 6th VFR 800 Header build The one on the right has the same amount of pleats and looks to be the same size as the k&n I have for my 4th gen. The part number is HA-0003. RVFR, 6/8/2017 at 0:42 PM [image: DSC02273_zpsssidb96d.jpg]
- 97 Low Fuel Indicator I have gone just over 40 miles after the light came on and there was no sound of gas in the tank when I opened it at the station.
- Pilot Road 4 Gt On A Non-7Th Gen. Vfr I have them on my 4th,rode them all last season no problems and will this coming season as well.
- Two Brothers Header Replication! Hopefully everyone can agree from here out to not send anymore emails concerning the 4th gen exhaust to Tyga to avoid any further confusion,it's only hurting our chances to actually make this happen.
- Two Brothers Header Replication! It was posted on page two that they wouldn't be looking into this until the 800 project was finished so I don't see any reason anyone should be contacting them about it.
- Two Brothers Header Replication! TheStig Hi Alhazred. I speak to Paul every now & then about other stuff and he mentioned the header again, so I shared what he'd said that's all. Being in Japan, I don't really have any intention of dealing with Tyga…
- Two Brothers Header Replication! We haven't decided which header to have replicated or even have an official list of who is committed yet. I thought Stryker was heading this one up,I think we need to stick with one person dealing with Tyga to get this…
- Performance Mods For Rc36 JZH Alhazred Factory pro used to do an ignition advance mod,I think it just involved sending them your flywheel and they modified it to 5 deg advance. I sent them an email and they don't seem to have any info on it…
- Performance Mods For Rc36 Factory pro used to do an ignition advance mod,I think it just involved sending them your flywheel and they modified it to 5 deg advance. I sent them an email and they don't seem to have any info on it other than they…
- Two Brothers Header Replication! My offer still stands to help make this happen if Tyga goes for it.
- Coolant Pooling There are three drain bolts,one by the pump and two under the front exhaust outlets. Did you take those out?
- Advice On Chain/sprocket Replacement There is a company called Ognibene that makes rubber damped sprockets,they have one that will fit the 750
- Two Brothers Header Replication! coupedupsubie I got lucky and my 4th gen came with the TBR left exit low mount. From what I was told I'm the third owner. The original owner put the TBR system on and was unhappy with how it ran. He supposedly called…
- Two Brothers Header Replication! They have 21 people committed at 600 usd a pop in the VFR800 Tyga thread. Where do you come up with this idea that everyone will back out? Did you start a thread about reproducing a VFR750 exhaust system and we all…
- Two Brothers Header Replication! The 4-1 is left side high mount and the 4-2-1 is right side low mount, both headers exit by the left foot peg.
- Two Brothers Header Replication! That's pretty cool. I currently own both styles of the headers that Two Bros made for the 750's,neither of them have the stock exit location and they are slightly different from each other so there would have to some…
- Daugherty Front And Rear Suspension Install How much did the shipping cost?
- Got Busy Yesterday Did not think so.....oh well.....so i got busy once again and got the stem out....sure glad I have a pneumatic impact wrench to get that top nut off since the forks are already on their way to Jamie!! Got the races out…
- 4Th Gen Tires I have PR4 gt's on my bike and so far they have been fantastic,I wouldn't think twice about getting them again. How long have you had them? I've had them for a few weeks now.I don't ride really aggressive but I can't…
- 4Th Gen Tires I have PR4 gt's on my bike and so far they have been fantastic,I wouldn't think twice about getting them again.
- '97 Muffler Choices? That was a two bros header with a d&d can. The Delkevic would be a good choice if you can't wait.I had one that came with my 4th gen and can't say anything bad about it but I would hold out for something cooler to come…
- Ride Height Lowering, Rc 36 Ii - Help The stock seat height should be around 31.5 inches or 800mm.
- Pilot road 4 gt on my 4th gen How much do you weigh yerself? I weigh 230+ all geared up,that will go down a bit in the warmer months. where did you get them for dirt cheap??? I've got a PR 4 gt on my 94 and they seem to work pretty good, but if your…
- Pilot road 4 gt on my 4th gen I picked up a low km take off set of PR4s for dirt cheap and didn't realize until after that the gt version is for a heavier bike. What do you guys think? Should I sell or trade them off for a more appropriate set or…
- V4 Went Bang On The Way Home The Other Night.... I would try to get my money back from that shop,pull the head and hope there was only bent valves in there.Then I would buy a good used head and take it somewhere else to get it put in or just replace the engine if…
- V4 Went Bang On The Way Home The Other Night.... It looks like the electrode and insulator came off inside the cylinder,that plug look REALLY old too. When I got my VFR I found the plugs not even finger tight after a couple of tanks of bad mileage,I think it would…
- Considering A 1994 Vfr750 If it's in good shape and taken care of don't second guess it,the only time you'll find a 4th gen owner in regret is after they sell one. There will likely be some cracking around the tail section of the fairing but…
- Help Solve My Stuttering............ Thanks,I was hoping to find some for my 4th gen a bit cheaper.I didn't realize there was such a price difference.
- Help Solve My Stuttering............ Where did you find the carb boots for 10 bucks a piece?
- How To Replace Coolant Hoses--The Ones Under The Carbs? Keep an eye on the "square" rubbers between lower rim and top of frame spare so that they donot come off. Those are what I mean,one of the damn things fall off every time usually between the frame and carbs somewhere.
- How To Replace Coolant Hoses--The Ones Under The Carbs? It's really not that hard to take the carbs off,I have more trouble getting the tank on with the rubber cushions in place than popping the carbs on and off.
- Has Anyone Used These No Cut Ebay 4Th Gen Sliders? These are what you want,they attach to the motor mount and you only have to drill the duct not the fairing. http://www.rdmoto.eu/motocykl/53/product/42996
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.