Member record · ID 10882
airwalk
69 posts recovered 0 threads started First seen 2 Jan 2011 Last seen 2 Feb 2026
Recent posts
Last 50 of 69- 750 flat spot There’s also a small foam filter in the end of hose feeding carbs with atmospheric pressure, often overlooked & can deteriorate badly. If it’s restricting free air flow symptoms will be pretty much as described, #6 in…
- Tyre alternative vfr400r nc21 New minimum length chain I meant to say
- Tyre alternative vfr400r nc21 That 130/80 is the Oem size for my ‘’86vfr, I’m using a 130/90 with no issues, slightly more “sensitive” steering, tiny bit higher (minimum length) it might be a bit tight to get the wheel reinstalled
- Overheating main fuse but need to move the bike 2 miles. I’ve had similar overheating with a few bayonet style fuse holders, some to the melting stage which is too close a call(fire!)for me. My current solution is to use bolt on types which is working well, pia to change but…
- 2015 VFR800DLX No Start… I know you’ve checked the associated fuses but why not replace them, it wouldn’t be impossible for a fuse to look/test ok but still not pass power, even though the meter says otherwise. I’ve seen it happen more than…
- Thick bearing being replaced by smaller twins ?? I had a similar situation, same year bike, as I recall the brgs were hard to find because they are a Honda only size, no std offerings would fit. As long as the dimensions are an exact match to the Oem parts you should…
- Starter switch stuck on for 4 minutes while running - Bike no start, battery load tests good You’re sure to have luck of some kind, as it happens not always bad. After getting smoking hot that starter must be 1 in 10,000 for durable quality!😅
- Starter switch stuck on for 4 minutes while running - Bike no start, battery load tests good Try starting with a working starter motor, yours is likely no longer functional. If it doesn’t work as usual the clutch case/ cover will have to be removed so the starter clutch & associated gear(s)can be inspected,…
- shindengen FH020 charging query I recall how good it felt to finally solve an electrical issue on my ‘86(took weeks), congratulation & kudos 😅
- shindengen FH020 charging query Testing the ac w/bulb could show a phase that’s weaker in output but you should use a 60-100 watt ac(household) bulb. I believe the rotor size&stator changed 2003 on as you say, dimensions would be available from a…
- shindengen FH020 charging query I would suspect stator fault(s) before loss of magnetic properties unless the magnets are electro type, which these aren’t. But this puzzle has come to the grasping straws stage, worth a try if another rotor handy.…
- shindengen FH020 charging query I’ll be very interested in your solution. I’ve got an older(‘86) vfr that charges @13.7 & has done for so long I don’t recall it ever being higher, although years ago I changed rr, wiring , etc. chasing a 14+ chg.rate…
- shindengen FH020 charging query Try fuse holder between rr & batt+, have had problems there a couple times. Most recent showed low & fluctuations on voltmeter while fuse remained intact, previous showed steady & correct meter readings until it finally…
- 2007 VFR800 blowing fuses post winter storage Yes, should be 30 amp
- Recall alert on VFR1200 Failing fuel pump impellers, bad material/manufacturing
- VF500F2 Aka MBD Incubation Period At Least 52 Years Guessing someone added aftermarket type pad & those are snaps to mount it
- Any fellow '99 owners can help me with understanding key blanks? For ‘95 my local charged $60 to cut from code, works on/off fine but won’t operate steering lock plunger feature of OEM switch. Tried an “online” cutter service from Germany first($25), waited 2 months for it & got a…
- Got a RC24 again...... Hopefully they work!
- Got a RC24 again...... Keny..found used on e-bay from the US, so far they’ve worked fine. If you’re desperate I could send along the good 1 that I saved, wiring could be wrong color but that won’t stop the electrons flowing!
- Got a RC24 again...... Exact same issue on my ‘86, after exhausting trouble shooting & replacing parts that are/were fine(ecm,etc) found 1 of the 2 pulser coils near starter clutch would cut out totally when heated. Oddly enough the other 1…
- Service from authorized dealers on older bikes My’95 has about 350,000 km, maybe 1 (mis) adj of valve gaps before I got it years ago(2000?) with 30-ish K on odo. Corrected that & haven’t touched since..
- Slow burn 5th gen build - old skool kool! To get grease behind rollers heat it until fairly thin & apply with soft clean toothbrush or similar. Good luck reusing that pair of ball bearings, they’re likely damaged even if you can’t feel/detect it…
- Slow burn 5th gen build - old skool kool! When I did this job on my ‘95 it was a real hassle getting those 2 brgs inside the hub/adjuster piece. Hope you have better luck(think they were NLA from Honda in Canada, had to source from a brg supply in the next…
- VFR Electrical outage when pressing starter button Have a look @ all wiring connections on solenoid. If repairs needed use ox-gard on refreshed parts, it helps with corrosion & “connectivity”..
- Clicking Starting Relay Still cant resist following along on interesting threads, despite having been left hanging too many times over the years. Must be another of my character flaws ..
- Is my 24 year old starter motor due for a rebuild or replacement? My’95 developed a “sticky” start button years ago, being lazy I put a short piece of surgical tubing behind the lever/button, acts like a return spring & still works well. If my digital abilities weren’t so lacking I’d…
- Valve Check! Any ideas on how much clearance remained? Most of the spec or hardly any...
- This is what happens... Only thing I do to stop the wiggle is touch the grips lightly, hoping Honda is right as I’m too lazy for the brg change, works fine & not dangerous...
- This is what happens... Wearing a set on my ‘96, no cupping yet but can’t stop an irritating deceleration shake. Doesn’t hurt anything, just driving me to distraction. Tried everything short of changing to a different tire, nothing I’ve done…
- How long can you leave a bike unused before fuel causes problems? Use a preservative, full tank, mine lasts for months easily, occasionally years, even the low octane type that “may contain” up to 10% ethanol. However, all my bikes are carb’d, fuel injected types could be a different…
- New Stator Dimensions ? How much “smaller”? I doubt the magnets in the rotor will work very well if they’re not close enough to the stator coils/windings. Better do more research, some of the earlier gen 6 reportedly had different sized…
- Headlight Voltage?? Help ?? If you don’t have one attach/mount a digital volt meter, monitor actual readings @ battery while running or even shut off. Running shouldn’t exceed 14.5-14.9, also some less $”aftermarket” bulbs don’t last worth a damn.…
- Howdy everyone! New to VFRD. From New Jersey. Need help/advice “Roadster”, may save those stators if series type is chosen instead of shunt style. If it works it’ll be worthwhile...
- Engine misfiring when warm ‘08 V-tec, if my research is correct( he specifies A-6 model/ version)
- What did you do to your VFR Today? Yes, shows how procrastination can pay off in a way, also that luck isn’t always the bad kind. May not be a favourable comment on my maintenance practice though!
- What did you do to your VFR Today? Changed shock. About time too, 317K km! Bottom needle bearing good but bumper totally shot, can only imagine what it’s like inside..dr
- 54 yrs old and back on the roads 6th gen 800. Soon 2B 76, 1stgen & 2 4ths, now I feel old. 👀
- Different needle washer in same 4th carbs A previous owner likely did this to “improve” (richen) mid-range throttle response
- 86 VFR 700cc Went down this rabbit hole with mine a few months ago. One of the pair of pulser coils would fail hot, replacing it solved the problem. They’re only available in pairs, used(eBay?), so you’re gambling the replacements…
- Tire question: Does anybody run Conti Motion on a 3+4 gen VFR? Have them on my ‘96, only a few dry rides so far but they seem fine, maybe a bit quicker profile than Michelin’s. Seem agile on turn in/lean..
- any preferences on 1998 vfr 800 Fi oil filer Mobil1, preference #110(longer) but #108(oem length) is fine, changed @ approx. 10k km or every other 5K km oil service.
- cold exhaust on cylinder 3 gas 50/50 mix oil and gas Very low or nil compression would do it. Curious to learn if this ever is solved/resolved...
- Quicker Handling Due to availability circumstances, I’ve accidentally/incidentally found acceptable changes by using slightly larger tire on rear & smaller on front(about 10mm +/- sidewall dimensions). Sorta a bonus that came with…
- Chain Oiler debate You’re right, seems very difficult to find that topic on this forum/site, lotsa discussion elsewhere if you wanna wade through all the claims of “superior system” that exist. I have 1(cameleon), but only because I’ve…
- 1996 VFR750 Carb Woes from CA Could be worth checking condition of sub-air filter, I once put a “better” (denser) piece of foam in my ‘95 & it took me ages to track down why it was running so weird. Restricted the air flow to the carb diaphragms as…
- Maintenance tips 60-55 bulbs get too hot for the plastic sockets(parts no longer available new from Honda), but if the bulb prongs fit right any socket will work, as you say. Other sockets could even be made of plastic that’ll stand the…
- 1990 VFR750 Carb Settings Sounds a bit rich for lower throttle openings. You’ve changed a fair number of things that have some influence on air fuel ratio, washers under jet needles could be too thick, 2.5 turns out on idle mix screws is enough…
- Oil Fiter Options For The Honda. Same for mine, vfr only tho(‘96)
- Super weird starter issue may enjoy a new good battery, sounds like you might not have enough current for strong ignition, just enough to sorta operate starter & other loads
- Another RC36.1 Restoration if you research further youll find that most opinions have the dielectric as an insulator while oxgard is a conductor, to add confusion consider this.. which is more christian, catholic or protestant? i choose to…
Member profiles were not captured; this page is assembled from the posts that were. Post counts reflect what the archive recovered, not the forum's own totals.